Components

PRODUCT CATEGORY

Kenaier conveyor components include brackets, idler frames, pulley lagging, support accessories and spare parts used to keep belt conveyor systems stable and maintainable. These parts are often small compared with the whole conveyor, but they directly affect belt tracking, roller support, cleaning performance and replacement efficiency.

This category is suitable for buyers who are maintaining existing conveyor lines, replacing worn parts or matching components to a new system. Instead of selecting parts only by name, confirm installation position, belt width, frame standard, material condition and current equipment structure.

If you are unsure which component matches your conveyor, send photos, dimensions or drawings. Kenaier can review the operating position and recommend compatible parts.

Products

Rotating Brush Belt Cleaner for Conveyor Return Side Cleaning

The rotating brush cleaner is located under the return conveyor belt of the conveyor, which can effectively clean the adhesion on the roller surface and the bottom of the conveyor belt.
Return Belt Cleaner Air Section Type for Tail Pulley Protection
Spring Belt Cleaner for Self Adjusting Conveyor Carryback Removal

This cleaner adopts a spring structure, which can automatically adjust the blade, so that the blade plate maintains the best adhesion with the tape surface, cleans the tape adhesion, and eliminates the disadvantage of the alloy blade plate that is easy to damage the tape. Good elasticity, this cleaner uses the spring length adjustment device to automatically adjust the cleaning plate.
Secondary Belt Cleaner P Type for Conveyor Belt Return Cleaning

The P-type cleaner is installed on a stable working surface near the head wheel. It is used to remove the adhered materials near the bottom of the head wheel.
Primary Belt Cleaner H Type for Head Pulley Carryback Control

The H-type cleaner is installed near the head wheel, near the tangent point that is 15 degrees to the horizontal line of the head wheel center. It is used to remove adhered materials near the top of the head wheel.
Hydraulic Belt Tracking Bracket for Conveyor Deviation Correction

The hydraulic deviation correction bracket supports the hydraulic deviation correction device, and is composed of a self-aligning wheel composite pump composed of a self-aligning wheel and an oil pump, a combined oil cylinder composed of an integrated block and an oil cylinder, and an oil pipe mechanism.
Trough Idler Frame Bracket for Conveyor Roller Support Assemblies

The trough-shaped bracket is mainly suitable for the brackets on TD75 and DTⅡ. The main brackets include trough-shaped brackets, parallel brackets, self-aligning brackets, V-shaped brackets, etc.! The trough-shaped bracket is widely used.
Self Aligning Idler Bracket for Conveyor Belt Tracking Support

The trough-shaped bracket is mainly suitable for the brackets on TD75 and DTⅡ. The main brackets include trough-shaped brackets, parallel brackets, self-aligning brackets, V-shaped brackets, etc.! The trough-shaped bracket is widely used.
Tapered Conveyor Rollers for Self Aligning Belt Tracking Support

The tapered rollers are divided into tapered upper centering rollers and tapered lower centering roller groups. The tapered rollers are wear-resistant and have a long service life.

1 2 3 NEXT END

Components

PRODUCT CATEGORY

Products

The rotating brush cleaner is located under the return conveyor belt of the conveyor, which can effectively clean the adhesion on the roller surface and the bottom of the conveyor belt.

The P-type cleaner is installed on a stable working surface near the head wheel. It is used to remove the adhered materials near the bottom of the head wheel.

The H-type cleaner is installed near the head wheel, near the tangent point that is 15 degrees to the horizontal line of the head wheel center. It is used to remove adhered materials near the top of the head wheel.

The trough-shaped bracket is mainly suitable for the brackets on TD75 and DTⅡ. The main brackets include trough-shaped brackets, parallel brackets, self-aligning brackets, V-shaped brackets, etc.! The trough-shaped bracket is widely used.

The trough-shaped bracket is mainly suitable for the brackets on TD75 and DTⅡ. The main brackets include trough-shaped brackets, parallel brackets, self-aligning brackets, V-shaped brackets, etc.! The trough-shaped bracket is widely used.

The tapered rollers are divided into tapered upper centering rollers and tapered lower centering roller groups. The tapered rollers are wear-resistant and have a long service life.

Free to contact us